Non-hydraulic lifting platform -equal safety device -dropping safety device is an important part of the construction lift
ing platform. The hydraulic docking bridge is a special auxiliary equipment for fast loading and unloading of goods. Its height adjustment function enables a bridge between the truck and the cargo platform of the warehouse. The forklift and other handling vehicles can directly drive into the truck for bulk loading and unloading through it. Called the loading and unloading platform. In order to eliminate the fall accident in the cage and ensure the safety of the crew, we must rely on it. Therefore, the anti-fall safety device is very strict in the factory test. Before leaving the factory, the legal inspection unit measures the torque, the critical speed measurement and the spring compression measurement, and each measurement is accompanied by a test report. After assembling on the building lifting platform, perform a drop test under the rated load. The lifting platform used on site must undergo a drop test every three months. For the two-year anti-falling safety device, it must be sent to the legal inspection unit for inspection, and then tested once a year. So far, very few people have been sent to inspect, and some sites have not even conducted a drop test every three months, thinking that their fall protection safety devices are okay, but they will not be able to perform the test in the event of an accident. Why not regularly test and send inspections based on the system? It is good to use units blindly, thinking that they are not bad. In fact, the quality of the anti-fall safety device can only be judged by testing and inspection, and it is impossible to determine whether it is good or bad in daily operation. It’s best to send it to the test early and test those that are unavailable on a regular basis. Only when we know what we think can we prevent the occurrence of serious accidents from the beginning. Safety switch The safety switch for lifting cage
is designed according to safety requirements. The hydraulic lifting platform is driven by steel wire ropes and is mostly used to transport goods. It is composed of tower, hanging basket, hoist, etc. The tower is generally a truss structure, which is pulled by cables to keep it upright. The hanging basket is welded with section steel and is a container for loading goods. The hoist is fixed on the ground, the wire rope is connected to the gondola through the pulley on the top of the tower, and the gondola is pulled to run up and down, and the operator controls it on the ground. There are fence door limit, cage door limit, top door limit, limit switch, upper and lower limit switch, heavy rope break protection switch, etc. In order to save the workload of some construction sites, some limit switches will be cancelled or short-circuited or damaged after timely maintenance. This is equivalent to the safety protection of these lines and buried potential accidents. For example, if the cage is to be fitted with a long object, the cage must be extended when the cage cannot be placed. In order to cancel the threshold position or ceiling threshold, the above-mentioned safety facilities are imperfect or incomplete, and the occupants are still subject to the same Way to carry. This illegal operation is a joke about people's lives. In order to avoid potential accidents, it is hoped that the leaders of all units will strengthen management and strictly require lifting cage maintenance personnel and operators to regularly check the safety and reliability of various safety switches. Stop accidents. The wear and tear of gears and racks are replaced on site. The operating conditions are poor. Cement, mortar and dust cannot be removed. The gears and racks are running in with each other, and the racks are still in use, so attention should be paid. platform is a kind of lifting machinery that vertically transports people or objects. It also refers to the equipment for vertical transportation in logistics systems such as factories and automatic warehouses. The lifting cage platform is often equipped with a variety of flat transportation equipment as a connecting device for conveyor lines of different heights. It is generally driven by hydraulic pressure, so it is called hydraulic lifting platform. In addition to transporting goods at different heights, it is widely used in high-altitude installation and maintenance operations. As we all know, the tooth shape should be like a cantilever beam. When worn to a certain size, the gear must be replaced. To what extent will wear and tear cease to be used to replace new ones? When the normal length of the gear is worn from the normal size to less than the size, a new gear must be replaced, which can be measured with a 25% common standard. When the rack is worn, use the thickness of the rack to measure it. When the height of the rack drops from the height of the abrasive particles to a lower level, the rack must be replaced. However, many 'old-tooth' gears and rack lifting platforms are still in service on site to extend service. For safety reasons, new accessories must be replaced.
If you are looking to get started with suspended working platform
, it's important to find a quified . Let Wuxi Powerston Technology Co.,Ltd be your provider. Visit us at Powerston Construction Equipment.
Wuxi Powerston Technology Co.,Ltd will expand our presence in direct selling and lead the reinvention of the channel, offering an entrepreneurial opportunity that delivers superior earnings, recognition, service and support, making it easy and rewarding to be affiliated with Powerston and elevating the image of our industry.
Wuxi Powerston Technology Co.,Ltd will give you a suitable price for purchasing suspended working platform.
Wuxi Powerston Technology Co.,Ltd have been an established and popular company with an excellent track record for the best customer satisfaction.
Wuxi Powerston Technology Co.,Ltd manufactures suspended working platform with innovative facilities and professional operation.